332
Finally put up some shelving and wall mounted the dryer after living here for 5ish years. (media.piefed.social)
submitted 7 months ago by to c/dull_mens_club@lemmy.world
87 comments fedilink hide all child comments
 

Been doing a huge amount of work around the house lately in the holidays.

Currently power washing the pavers out back and filling the joins with sand. Should be more fun tomorrow.

you are viewing a single comment's thread
view the rest of the comments
[–] [S] 62 points 7 months ago (2 children)

Yes thats correct, the official instructions tell you to mount it upside down and the kit it comes with only works one way.

I've always found it irritating on others I've done over the years but there ya go.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 4 child comments
    •
  • [–] 53 points 7 months ago (1 child)

    Never seen this done before. Glad to hear it’s a supported configuration.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] 26 points 7 months ago (1 child)

    Same. I was genuinely scratching my head before I came to the comments. Reaching the controls didn't even enter my mind 😂. I've seen stacked/combo units before, but never a wall mounted dryer.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] [S] 49 points 7 months ago (4 children)

    Maybe this is less dull than I thought - perhaps mildly interesting?

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 8 child comments
    •
  • [–] 7 points 7 months ago (1 child)

    Does this mean before you had it mounted it was actually upside down? Like the controls and all the text was upside down?

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] [S] 3 points 7 months ago (1 child)

    No it was sitting right side up on the floor

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] 1 point 7 months ago (1 child)

    I get that. But then were all the labels on the controls upside down?

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] [S] 2 points 7 months ago (1 child)

    Nah it was sitting right side up on the floor - they are upside down now

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] 1 point 7 months ago (2 children)

    But you said elsewhere it was intended to be mounted this way? I’m so confused.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 4 child comments
    •
  • [–] 4 points 7 months ago* (1 child)

    Not OP, but fellow Aussie who's mounted the odd dryer upside down on the wall like this. The dryer is able to be used either way up. The ones I've done tended to come with stickers to place over the control panel so the text is readable again. I've never bothered.

    Example: https://www.fisherpaykel.com/au/laundry/dryers/vented/6kg-series-3-vented-dryer-auto-sensing-full-reverse-tumbling-de6060m2-92277.html

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] [S] 3 points 7 months ago

    Sorry, it is an option to be mounted on the wall.

    Normally it would sit right side up in a stack or on the floor, by wall mounting you have to flip it so the controls are at the bottom which turns them upside down.

    Its not an issue cause like I said in another comment its a number dial and a hot/cold toggle, nothing hard to figure out

  • permalink
  • fedilink
  • source
  • parent