▲ 135 ▼ Finally finished my first RC car (lemmy.world) submitted 2 years ago by UserNotFound@lemmy.world to c/3dprinting@lemmy.world 9 comments fedilink hide all child comments I finally finished model 7 (Buggy) from 3dsets. It was fun to build, but mistake to take it in forest (one screw loose near one rear wheel).
[–] Asstronaut@lemmy.world 3 points 2 years ago (1 child) Great stuff! How did you find their gearboxes and driveline strength? permalink fedilink source hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 2 points 2 years ago* (last edited 2 years ago) (1 child) There is belt gearbox, I found belts in my local shop. Or how did you mean your questions? I found all in non printed parts bom permalink fedilink source parent hideshow 2 child comments replies: [–] Asstronaut@lemmy.world 3 points 2 years ago (1 child) Sorry! in English “how did/do you find” something also means what is your opinion on something. I meant to ask what do you think of the driveline, is it strong, easy to lubricate, did the parts fit well? I’ve been thinking of building one permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 4 points 2 years ago* (1 child) I see, thanks for explain. Driveline is no need to lubricate, because it's belt drive system(at least in Model 7). Parts fit well, bearings, belts etc (although, that depends on how well calibrated is your printer). I think that system is strong enough. I built it with brushless motor and it's wild. Only challenging parts were ball joints. I had problems to fit them in place, but I found a way. permalink fedilink source parent hideshow 2 child comments replies: [–] Asstronaut@lemmy.world 2 points 2 years ago (1 child) Awesome thanks for the info! Which filaments did you use? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 2 points 2 years ago* (1 child) PLA: Prusament Lipstick Red (body) Polyterra Charcoal Black (chassis) Polyterra Fossil grey (inside) Filament PM(Czech brand) graphite black (seats) Filament PM white Filament PM Pearl Red (cage) Fillamentum Clear (for lights) ASA: Prusament Lipstick Red (for few parts) permalink fedilink source parent hideshow 2 child comments replies: [–] MrAnderson@feddit.nl 1 point 2 years ago (1 child) I wasn't expecting plain PLA! Are there any issues with warping due to heat from the motor? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 1 point 2 years ago It's recommended to use PC or ASA for motor parts. I used ASA permalink fedilink source parent
[–] UserNotFound@lemmy.world [S] 2 points 2 years ago* (last edited 2 years ago) (1 child) There is belt gearbox, I found belts in my local shop. Or how did you mean your questions? I found all in non printed parts bom permalink fedilink source parent hideshow 2 child comments replies: [–] Asstronaut@lemmy.world 3 points 2 years ago (1 child) Sorry! in English “how did/do you find” something also means what is your opinion on something. I meant to ask what do you think of the driveline, is it strong, easy to lubricate, did the parts fit well? I’ve been thinking of building one permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 4 points 2 years ago* (1 child) I see, thanks for explain. Driveline is no need to lubricate, because it's belt drive system(at least in Model 7). Parts fit well, bearings, belts etc (although, that depends on how well calibrated is your printer). I think that system is strong enough. I built it with brushless motor and it's wild. Only challenging parts were ball joints. I had problems to fit them in place, but I found a way. permalink fedilink source parent hideshow 2 child comments replies: [–] Asstronaut@lemmy.world 2 points 2 years ago (1 child) Awesome thanks for the info! Which filaments did you use? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 2 points 2 years ago* (1 child) PLA: Prusament Lipstick Red (body) Polyterra Charcoal Black (chassis) Polyterra Fossil grey (inside) Filament PM(Czech brand) graphite black (seats) Filament PM white Filament PM Pearl Red (cage) Fillamentum Clear (for lights) ASA: Prusament Lipstick Red (for few parts) permalink fedilink source parent hideshow 2 child comments replies: [–] MrAnderson@feddit.nl 1 point 2 years ago (1 child) I wasn't expecting plain PLA! Are there any issues with warping due to heat from the motor? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 1 point 2 years ago It's recommended to use PC or ASA for motor parts. I used ASA permalink fedilink source parent
[–] Asstronaut@lemmy.world 3 points 2 years ago (1 child) Sorry! in English “how did/do you find” something also means what is your opinion on something. I meant to ask what do you think of the driveline, is it strong, easy to lubricate, did the parts fit well? I’ve been thinking of building one permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 4 points 2 years ago* (1 child) I see, thanks for explain. Driveline is no need to lubricate, because it's belt drive system(at least in Model 7). Parts fit well, bearings, belts etc (although, that depends on how well calibrated is your printer). I think that system is strong enough. I built it with brushless motor and it's wild. Only challenging parts were ball joints. I had problems to fit them in place, but I found a way. permalink fedilink source parent hideshow 2 child comments replies: [–] Asstronaut@lemmy.world 2 points 2 years ago (1 child) Awesome thanks for the info! Which filaments did you use? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 2 points 2 years ago* (1 child) PLA: Prusament Lipstick Red (body) Polyterra Charcoal Black (chassis) Polyterra Fossil grey (inside) Filament PM(Czech brand) graphite black (seats) Filament PM white Filament PM Pearl Red (cage) Fillamentum Clear (for lights) ASA: Prusament Lipstick Red (for few parts) permalink fedilink source parent hideshow 2 child comments replies: [–] MrAnderson@feddit.nl 1 point 2 years ago (1 child) I wasn't expecting plain PLA! Are there any issues with warping due to heat from the motor? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 1 point 2 years ago It's recommended to use PC or ASA for motor parts. I used ASA permalink fedilink source parent
[–] UserNotFound@lemmy.world [S] 4 points 2 years ago* (1 child) I see, thanks for explain. Driveline is no need to lubricate, because it's belt drive system(at least in Model 7). Parts fit well, bearings, belts etc (although, that depends on how well calibrated is your printer). I think that system is strong enough. I built it with brushless motor and it's wild. Only challenging parts were ball joints. I had problems to fit them in place, but I found a way. permalink fedilink source parent hideshow 2 child comments replies: [–] Asstronaut@lemmy.world 2 points 2 years ago (1 child) Awesome thanks for the info! Which filaments did you use? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 2 points 2 years ago* (1 child) PLA: Prusament Lipstick Red (body) Polyterra Charcoal Black (chassis) Polyterra Fossil grey (inside) Filament PM(Czech brand) graphite black (seats) Filament PM white Filament PM Pearl Red (cage) Fillamentum Clear (for lights) ASA: Prusament Lipstick Red (for few parts) permalink fedilink source parent hideshow 2 child comments replies: [–] MrAnderson@feddit.nl 1 point 2 years ago (1 child) I wasn't expecting plain PLA! Are there any issues with warping due to heat from the motor? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 1 point 2 years ago It's recommended to use PC or ASA for motor parts. I used ASA permalink fedilink source parent
[–] Asstronaut@lemmy.world 2 points 2 years ago (1 child) Awesome thanks for the info! Which filaments did you use? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 2 points 2 years ago* (1 child) PLA: Prusament Lipstick Red (body) Polyterra Charcoal Black (chassis) Polyterra Fossil grey (inside) Filament PM(Czech brand) graphite black (seats) Filament PM white Filament PM Pearl Red (cage) Fillamentum Clear (for lights) ASA: Prusament Lipstick Red (for few parts) permalink fedilink source parent hideshow 2 child comments replies: [–] MrAnderson@feddit.nl 1 point 2 years ago (1 child) I wasn't expecting plain PLA! Are there any issues with warping due to heat from the motor? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 1 point 2 years ago It's recommended to use PC or ASA for motor parts. I used ASA permalink fedilink source parent
[–] UserNotFound@lemmy.world [S] 2 points 2 years ago* (1 child) PLA: Prusament Lipstick Red (body) Polyterra Charcoal Black (chassis) Polyterra Fossil grey (inside) Filament PM(Czech brand) graphite black (seats) Filament PM white Filament PM Pearl Red (cage) Fillamentum Clear (for lights) ASA: Prusament Lipstick Red (for few parts) permalink fedilink source parent hideshow 2 child comments replies: [–] MrAnderson@feddit.nl 1 point 2 years ago (1 child) I wasn't expecting plain PLA! Are there any issues with warping due to heat from the motor? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 1 point 2 years ago It's recommended to use PC or ASA for motor parts. I used ASA permalink fedilink source parent
[–] MrAnderson@feddit.nl 1 point 2 years ago (1 child) I wasn't expecting plain PLA! Are there any issues with warping due to heat from the motor? permalink fedilink source parent hideshow 2 child comments replies: [–] UserNotFound@lemmy.world [S] 1 point 2 years ago It's recommended to use PC or ASA for motor parts. I used ASA permalink fedilink source parent
[–] UserNotFound@lemmy.world [S] 1 point 2 years ago It's recommended to use PC or ASA for motor parts. I used ASA permalink fedilink source parent
