9
Synology DS215j NAS - time for an upgrade? (feddit.de)
submitted 2 years ago by to c/selfhosted@lemmy.world
11 comments fedilink hide all child comments
 

I've had this box for almost ten years now, so I've been thinking about getting something new. Looking at the market, the new systems don't seem to be all that much more advanced, though. So my question is, should I get a new one or just keep the old box and swap out the drives? What can a new NAS do that my old one can't? And what kind of drives should I get? I have 2 TB WD Red something, is that still a good choice? I'd move up to 4 TB, of course. This box is only used as backup for my home stuff and a small business, I'm primarily concerned with reliability.

you are viewing a single comment's thread
view the rest of the comments
[–] 8 points 2 years ago* (1 child)

Why would you buy something new if your current solution works and your requirements don't change? Just keep it.

  • permalink
  • fedilink
  • source
  • hideshow 2 child comments
    •
  • [–] [S] 3 points 2 years ago* (3 children)

    I'm concerned about those drives. While they're not under a lot of load, every drive will fail eventually.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 6 child comments
    •
  • [–] 7 points 2 years ago (1 child)

    I’m concerned about those drives. While they’re not under a lot of load, every drive will fail eventually.

    Go into your storage manager in DSM and check the drive health.

    You could always replace failing drives on the same NAS, but replacing the NAS just to replace it seems like a waste of money, unless your needs have changed.

    Provided that you have a backup solution (a NAS isn't a backup solution on its own), then you should be covered even if the drive(s) fail.

    FWIW, I only use Seagate Ironwolf drives in my NAS.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] [S] 0 points 2 years ago (1 child)

    Everything looks fine in DSM.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] 3 points 2 years ago

    I wouldn't worry, then. You'll typically have a some kind of warning when a drive begins to fail. Keep your backups regular, and replace drives when needed.

    I have my DSM set up to do a drive health check every month, and I'll get an email with the results. Gives me piece of mind.

  • permalink
  • fedilink
  • source
  • parent
  • [–] 2 points 2 years ago (1 child)

    Agreed, if the box works for you I'd look at cycling out the drives - 10 years is a long time for spinning disks to last and every day is another day closer to a failure.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •
  • [–] 3 points 2 years ago

    So just swap new drives in one at a time, after backing your data up just in case. I upgraded mine to 4x10 drives 3-4 years ago, and its painless as long as you wait for the resilvering process to complete.

  • permalink
  • fedilink
  • source
  • parent
  • [–] 2 points 2 years ago (1 child)

    Have you checked the SMART values of your drives? Do they give you a reason for your concerns?

    Anyhow, you should never be in a position where you need to worry about drive failure. If the data is important, back it up separatly. If it isn't, well, don't sweat it then.

  • permalink
  • fedilink
  • source
  • parent
  • hideshow 2 child comments
    •